Sensors problems

8 reports

Rissa from United States 9 years ago

I have been told that by changing all the coils the problem should be solved. If the scanner detects which of the cylinders is having a coil failure you can then replace only the damaged ones. Tell me if I could help you please.

Field from United States 9 years ago

I personally believe that your problem is that your car has not been washed with a carburetor cleaner when the tune was made.

Best answer (according to Rissa)

artelepsa from United States 9 years ago

I had your same problem and the cause ended up being an ignition coil. Once it was detected which was the damaged coil with the code errors in the dashboard, it was replaced and the problem was solved.

Roshni from United Kingdom 3 months ago

Excuse me sir frod escape not power comming why .... New plug im all fuse cheking but i canot dicted this compalint ... Sir pls tell me whtais tha complaints

Comment

Stalling when first starting

Ford Escape 2005 4x4 V6 Ford Escape 196000 miles

My Escape died, had it towed, was diagnosed as an airflow sensor. Had it replaced and drove it home. It stalled on the way home at light, restarted, revved engine and it ran great. Get in next am and it started , idled fine, put in drive and it stalls, restarted, revved engine and it ran fine again, same thing this am. What the heck?

Kellie from Canada 7 years ago

2 reports

Kellie from Canada 7 years ago

Update, took it into a Ford dealership to have a diagnostic scan done. 2 hours later, turns out my mechanic put in an after market airflow sensor, it ran bad codes. Cleaned and put old sensor back in, cleaned idle controll valve and updated codes. Runs great.

Comment

Engine light on in dash panel

Ford Escape 2010 SUV 2.3 Ltr. 4 cyl 85000 miles

Had torque converter lock up problem , the transmission was change and after that the engine light in dash has been coming on. Have fitted two new Ego sensors $$$$$$ as fault code said it was that area. No one can fix it
Help please !!!!!!!!
Cheers Tim Lucas

Timbo from Australia 6 years ago

1 reply

Timbo from Australia 6 years ago

All good ,
Have had S/hand exhaust catalyst fitted , now been 5 days and No light on. Cheers Tim 🍺🍺👍

Comment

Hill start assist not available abs and traction control light on

Ford Escape 2015 Se 136000 miles

Car runs and drives great. Not had any problems till now. The obd port doesn't work. So I can't have the system checked. But I have changed the breaks and abs sensors. And still the same problem.

ToxicCupCake from United States a year ago

7 reports

Freedom from United States 7 months ago

My BlueDriver claims that both rear wheel speed sensors have wrong part installed. I've read that i need to remove and clean, cross reference part numbers that are etched on them, also check wiring and anything else related to them. I haven't attempted this yet. First, i need to fix the battery drain issue and then emissions issues, then the abs will get its turn.

Comment

Electrical, random no start trans position sensor low voltage

Ford Escape 2013 Se 2.0 4x4 220000 miles

Was driving and car shut off. Tried plugging in scanner and it had power but wouldn’t communicate. Ecm relay was clicking multiple times. Towed to shop. They replaced fuse box and now it will operate normal most of the time. There is a code for transmission range sensor that’s located internally. Opened up trans and replaced. No change. Car will randomly think it’s in D as soon as you insert the key to start it. Turn key off and on and will usually start. Sometimes have to turn key off and wait for the display to power off and then it will start. Also when shutting engine off it will engage starter for a split second and make contact with fly wheel to abruptly stop the engine.

Lost from United States 3 months ago