My car is 2014 Nissan amlera, it stalls after every few kilomiter while driving ?

Good afternoon, I have a Nissan Almera 2007, which starts but does not accelerate. The first failure that appeared and was detected by the scanner was a crankshaft sensor damage. It was replaced together with a coil that was failing too. The car worked properly for some days, until the engine started vibrating and losing power. This got worse with time and, today, it does not accelerate nor work properly any longer. I've checked the rear stop lights and they are working. When changing the gear to reverse the car, it usually stalls.

All coils are not sparking. So the engine is not starting o

My car does not accelerate, it loses power instead. It has been checked with three different scanners but no failure was indicated. I've checked the fuel pressure and it is 48 pounds. I've changed the positions of the camshaft and crankshaft sensors as they are the same, I've cleaned the injectors, the throttle body, the MAF sensor, but the car is still the same. Has anyone had this problem? I have my doubts with the VVT valve as, if it fails, it is not detected by the ECU and it affects the engine time and performance.

Even though the four coils are working, coil number 1 has no spark. I was told this has to do with a computer failure. The strange thing is that sometimes it works and others it does not. I've already changed all the coils and only one of them does not spark. What can it be?

When I press the brake pedal there is a loud audible noise and if I use the left indicator ant the same time the noise becomes much louder. If I use the left indicator without touching the brake pedal then the radio light flashes with the indicator. The indicator light on the left rear also just stays on. I've creared the DTC several times to cancel the engine management light but as soon as I drive again and use the brake pedal, the engine management light comes on again.

Engine turn over fuel is good

My car jerks, the check indicator is turned on and the revolutions needle is unstable. Both the crankshaft and camshaft sensors have been replaced, but the failure remains and it keeps indicating there is a problem with the crankshaft sensor. I do not know what else to do, can you help me please? Thank you in advance.

The immobilizer light is turned on, which indicates there is a failure in the NATS or immobilizer system. The vehicle occasionally stalls and starts without a problem. But there are some other occasions, which have been more frequent lately, in which the engine does not start working again after it stalls.

Not the coils not the ecu not the sensors. What else can it be?

It starts easily but stalls anytime i drive at less than 60km,the jerking is worse when speed is low but when it gets to 70km and above it accelerates normally. I changed the c2 cramshAft sensors and air filter its still the same. Pls help me

When the ac fan and radiator fan are on,the engine light comes on. When the fans are off, the engine light goes off. I have changed the air filter and alternator. I also did a diagnostic check but no codes. I cleaned the throttle body and used an addictive. The car still cuts out.

Check engine light off doesn't start

Since January my car has stopped on me about 6 times now. The AA was convinced the first time that it was the fuel pump but it turned out to be the fuse to the Spark Plugs had gone. Each time the fuse is changed and I drive again no problem until it happens again. The car has been in the garage various times. Spark Plugs were changed, a thorough check of wiring, bits clean up and replaced and yesterday all 4 coils were replaced. Today it happened again. I had only just started the car up and driven less than 10 feet. It doesn't always happen from cold although 3 have been from cold and 3 from… Read complete

Help me or advice me how to fix this problem

I have changed the fuel pump and spark plugs but it jerks specially when it's hot

Hi, I have an Almera which is really hard to start working. Once it finally does, it remains stable for a while but, when trying to accelerate it, the engine vibrates and stalls.

Morning
I drive Nissan almer 2002 model. When I start my car engine running only but is not start, help me please what was the problem of this please?

A client brought me his nissan almera vehicle was in a accident on the left frond side after the panel beaters finished he drove 300km home where the car stalled and since then the fuel pump doesnt prime there is no spark and no engine check light i checked wiring replaced cam and crank sensors fitted new coils changed out all fuses and relays still no start i did notice the security light flashes when i switch ign on it the light stays on

When this started, I sent it to a mechanic and he changed the plugs and serviced the injectors but the problem still persist.

The car just crank but no power to petrol pump and injectors and also no spark but i fuel pump fews are good

My Nissan almera 2002 is using dicktator management system now only 2 plug firing, 1and 4 no spark

The engine is stiff and the starter is unable to turn it nice

My car was having a problem of switching off whenever i start it. And when it gets to switch on it idles nicely and drives perfectly on the highway but it stalls at times when i do urban driving. The mechanic said its the throttle body sensor so i changed it but now its staring well but has started jerking but it stalls better and it can drive , please help

What is the reason not to have power on injectors but coils got spark?

My main problem is that my car takes time to start as if my battery has a problem, I sometimes struggle in the morning.

Secondly, it's overheating for about 3 months now not sure if it's the head gasket is blown...any ideas what problems am I facing

Engine lacks power on accelation

At times while driving engine would start stiffiling and would have to excelerate a lot to keep it going. When come to a stop, engine power would die down almost to cut off, service light does not come on dashboard. Could this be the catalyst malfunctioning?

No spark on number 3 and 4 cilinder

Hi have just done my motor over but when i start can it over fuels and wets the spark plugs by the head can someone please help me as and i hav check the sensors and fixed but still does tge same.

Nissan Almera 1.6 Manual petrol engine suddenly cannot start after driving the car to the mechanic for normal servicing. He says only 2 plugs are firing. What might be the problem?

The car is cranking, the spark comes and goes what can be the problem

Car only cranks, engine light not becoming on

I have no spark ecu and key chip does not wana start the car

The crank sensor keep showing engine has been rebuild and after DTC clearing sensor has been replaced and timing has been checked

It does not open injectors for petrol to flow to the engine. I don't whether its a computer problem or what please help.

Good morning I have qg18 Nissan almera 2006 I have overhull the engine but now 2 and 4 is not getting spark. Ihave changed the oil around still does not get spark

My Nissan Almera 1.8 2005 starts normaly and after 25-30 km the engine stops working and can not be started 1-2 minutes, after starting, the problem repeats in shorter period. The check indicator is turned on. I have made computer diagnostic and it shows 3 errors:
P0340 cmp sen/circ-b1
P0011 int/v tim cont-b1
P1612 Chain of ECM-IMMU
Both the crankshaft and camshaft sensors have been replaced, but the failure remains and it keeps indicating there is a problem with the crankshaft sensor. I do not know what else to do, can you help me please? Thank you in advance.

Engine on tickover Idles at 1500 revs: driving , engine hunts between gear changes at 1800 to 2500 rpm